1. Installing the Intel GMA 500 graphics driver

The Ubuntu Wiki has all the necessary information here.

Basically one just needs to do as follows:

sudo add-apt-repository ppa:gma500/ppa
sudo apt-get update
sudo apt-get install poulsbo-driver-2d poulsbo-driver-3d poulsbo-config

UPDATE: The following step is no longer required.

Unfortunately the version as of this writing does not support Compiz and thus you won’t get any of the funky special effects. However, there is a workaround available as described in the Ubuntu Wiki:

wget http://dl.dropbox.com/u/1338581/poulsbo/poulsbo-config_0.1.2%7E1004um3_all.deb
sudo dpkg --install poulsbo-config_0.1.2~E1004um3_all.deb
sudo apt-get install compiz

2. Installing the Fujitsu Buttons driver (fjbtndrv)

In order to get the buttons and auto-rotation functionality working we will need to compile and install the latest version of fjbtndrv.
The most current version as of this writing is 2.2.1. Please make sure you download the latest version here.

sudo apt-get install libxrandr-dev libxtst-dev libxi-dev libhal-dev
wget http://sourceforge.net/projects/fjbtndrv/files/fjbtndrv/2.2.1/fjbtndrv-2.2.1.tar.gz/download
tar xvzf fjbtndrv-2.2.1.tar.gz
cd fjbtndrv-2.2.1
./configure
make
sudo make install

3. Installing the Fujitsu Touchscreen driver

The touchscreen is working somewhat with the included evdev driver. I could not find a way to calibrate the touch screen via xinput etc. So I went back to using zmiq2‘s touch screen driver available here.
Version 0.3.7 won’t compile because some important USB functions were renamed in kernel 2.6.35.
Straight from the kernel 2.6.35 changelog:

USB: rename usb_buffer_alloc() and usb_buffer_free() users

For more clearance what the functions actually do,

usb_buffer_alloc() is renamed to usb_alloc_coherent()
usb_buffer_free() is renamed to usb_free_coherent()

So, one either needs to patch the fujitsu_usb_touchscreen.c manually and replace every occurrence of the aforementioned function names or we just move on and use the already patched version provided by nerd65536. I mirrored the file he posted to the hosting service linked to in the comments section of zmiq’s blog post.

wget http://katastrophos.net/downloads/fujitsu-usb-touchscreen-0.3.8.tar.gz
tar xvzf fujitsu-usb-touchscreen-0.3.8.tar.gz
cd fujitsu-usb-touchscreen-0.3.8
make
sudo make install

In order to have the auto-rotation functionality of fjbtndrv working with the fujitsu-usb-touchscreen driver we need to add a new startup item: Click on System -> Preferences -> Startup Applications and click Add. Enter following

    Name: Fujitsu Touchscreen Auto-Rotation
    Command: /usr/bin/fujitsu-touchscreen-rotate.py
    Comment:

Click Add and Close the preferences dialog.

Finally, reboot the system.
Enter the BIOS and make sure that the setting Advanced -> Miscellaneous Configurations -> Touch Panel Setting is set to Tablet, ie. the same setting that is required to use the Tablet functionality in Win XP Tablet, Vista or Seven.

3.1. Calibrating the touchscreen

Once the system has booted and you are back on the Gnome desktop, start a Terminal session and run

fujitsu_touchscreen_calibration.py

to calibrate the touchscreen. Click on any corner of the visible screen (repeat a few times) and press the S key to save the settings.

3.2. Configuring the Right-Click feature

In order to get the feature “right-click by press and hold” go to System -> Preferences -> Mouse, click the tab “Accessibility” and check the option “Trigger secondary click by holding down the primary button“.

4. Fixing the repeating sound issue

If you are experiencing the Ubuntu startup jingle repeating over and over again, the snd_hda_intel module might have problems coping with the ALC269 chip in your device. In this case run the following command:

sudo gedit /etc/modprobe.d/alsa-base.conf

and add the following line to the end of the file:

options snd-hda-intel enable_msi=0

Save and finally reboot the system.

Here are some photos of the drive itself and how to install it in the U810. Note, the drive is 5 mm high and will fit into the U810 without any modifications.
Also keep in mind that the U1010 has a different connector (50-pin IDE instead of ZIF), so these ZIF-drives will not work here. However, there are reports on UMPC Portal that suggest that it is possible to get a replacement connector flat band cable for the U810 that is the 50pin IDE cable, so I guess it is also possible the other way around for the U1010.

Here are the obligatory benchmarks comparing the new SSD against the old Toshiba MK1011GAH 100 GB hard drive that was previously installed in the U810:

Needless to say that applications cold-launch a lot faster with the SSD. (Firefox with 12 add-ons: ~10 s before -> ~6 s after, Chrome: ~3 s before, ~1 s after, Thunderbird: ~8 s before -> ~3 s after).

Startup time was reduced quite a bit but not dramatically. However, returning from sleep and hibernate saw a huge improvement. Unfortunately I can not provide values of the old drive, so no comparison.
I did not notice longer battery run times. However, the whole system runs a lot cooler because the SSD naturally does not produce heat as extensive as the HDD did.

I am satisfied with this upgrade – especially since it has boosted compile-times when working with CodeGear RAD Studio and Delphi – due to the great performance when accessing, reading and writing small files. Your mileage may vary.

I just installed Windows 7 Business Build 7000 on my U810. It is quite nice actually and seems to run faster than Vista.

I installed the Vista drivers from the driver CD. The Setup.exe on the driver CD will complain that the operating system is unsupported. To circumvent this problem, just start the setup in Vista compatibility mode:
Right-click on “Setup.exe”, “Properties” -> “Compatibility” -> “Run this program in compatibility mode for:” “Windows Vista”.

Install these items:

Drivers
04. Button Driver
05. Camera Driver
07. Fingerprint sensor (driver)
08. FUJ02B1 Device Driver (HotKey Driver)
09. FUJ02E3 Device Driver (System Extension Driver)
11. Pen Driver
12. Pointer device driver

Utilities/Applications
03. Button Utilities
07. Fujitsu System Extension Utilities

I could not get the Auto-Rotation feature to work. Also, you’ll probably have to calibrate the touch screen.
I also disabled the power management feature of the FCL USB Pen Tablet in Device Manager (Right-click on “Human Interface Devices/FCL USB Pen Tablet”, “Properties” -> “Power Management” -> Disable “Allow the computer to turn off this device to save power”). This improves the response of the touch-screen/tablet.

Oh, and BTW, Windows 7 “only” uses 7.5 GB of disk space, whereas Vista uses 15 GB I think.